How to hang your artwork

Bringing your new art to life on the wall is the final step — and one of the most satisfying parts of the process. Whether you’ve chosen a framed print or a stretched canvas, this guide will help you hang it securely and beautifully.

Our framed prints come ready to hang with D-rings and a strong wire attached to the back of the frame. All you need to do is decide where your piece belongs and choose the right wall hardware.

Choosing the Right Hardware

For plasterboard walls (gyprock):

• Use picture hooks, toggle bolts, or self-drilling plasterboard anchors rated for the weight of your frame.
• Avoid simple nails unless the frame is very light — they can loosen over time.

For timber stud walls:

• If possible, screw directly into a stud for extra support.
• If no stud is available where you want to hang the piece, use a wall anchor suited for hollow walls.

For brick or concrete walls:

• Drill a pilot hole using a masonry bit, insert a wall plug, and then screw in a screw or hook.
• Use heavy-duty anchors for larger or heavier frames.

Supporting Larger Pieces

For artworks over about 80 cm wide (31 inches), or if the frame feels heavy (over 5–6 kg or 11lb), it’s best to use two hooks or screws. This spreads the weight evenly and helps keep your art level over time.

Our stretched and box frame canvases are designed to hang flush against the wall — creating a clean, modern gallery look. They don’t come with D-rings or wires pre-installed, as they’re meant to rest directly on the wall surface.

Benefits of the flush mount style

• Gives a sleek, professional “gallery wall” finish.
• Keeps the artwork close to the wall for a modern, minimalist look.
• Easy to position and realign if needed.

Hanging Options

1. Direct Screw Method (Recommended):

• Use two screws or nails into your wall spaced roughly one-quarter in from each side of the frame.
• Rest the inner edge of the frame directly on the screws so the canvas sits flat.
• Use wall plugs for brick or concrete and plasterboard anchors for gyprock.
• Use a spirit or laser level when adding multiple screw/nails to ensure the frame will hang straight.

2. Add Your Own Hanging Hardware (Optional):

If you prefer a traditional hanging setup, you can easily install your own hardware:

• For small canvases: a single sawtooth bracket at the top centre works well.
• For medium or large canvases: two sawtooth brackets near the top corners or a pair of D-rings with hanging wire offer extra security and flexibility.

Hardware Suggestions by Wall Type

For plasterboard walls:

• Use plasterboard anchors or picture hooks with angled pins.
• Choose weight-rated hardware for the size of your artwork.

For timber studs:

• Drive screws directly into the stud for maximum hold.

For brick or concrete walls:

• Drill a pilot hole with a masonry bit, insert a wall plug, and secure a screw or hook.
• For heavier canvases, use two screws or plugs to balance the weight.

Always check your hardware’s weight rating — and err on the side of stronger support.

If the frame leans forward slightly, shorten the wire or move the hooks higher.

For symmetrical alignment, measure from the floor or skirting board to the top edge of your art rather than estimating by eye.

Once hung, take a step back and view your piece from a few angles. Adjust the height so the centre of your artwork sits roughly at eye level (about 1.5 metres from the floor) — a simple rule galleries use to create harmony and balance across a space.

We want your art to hang beautifully and safely. Just remember, there’s always a bit of risk when drilling or nailing into your walls — hidden inside are the vital parts of your home, like wiring and plumbing.

To stay safe, use a stud finder or wall scanner before drilling. If you’d rather not tackle it yourself, a local handyman can easily take care of it for you.

By choosing to install hanging hardware, you accept responsibility for any risks involved — but with a little care and the right tools, you’ll have your new piece up perfectly in no time.